This excellent case from MDLRCASE has two 1U rows for Intellijel format 1U modules.
14U/126HP Performer Series Pro features:
- This case is compatible with both Pulp Logic / Erthenvar and Intellijel 1U format
- Choose your own rails configuration for top and bottom case halve
- 1U rows are Intellijel format
- 12mm birchwood fully nailed and glued construction
- Sprayed with a special 2-layer black protective coating
- Detachable middle ring/spacer allows modules to be fully-patched during transport
- Spacer functions as a rock-solid stand when the case is open
- Flush-mounted rails allow the modules to be mounted even with the sides of the case
- Top and bottom sections can be detached and set up side-by-side as two separate 7U cases
- Twelve 126HP rails with M3 threaded inserts
- Two 45W or 85W MDLR PWR powered busboards (80 power headers in total)
- Two MDLR PWR extension boards (total of 14 extra headers)
- Total output (both case halves) 45W 4A on 12V, 2.5A on -12V and 3A on 5V
- Total output (both case halves) 85W 8A on 12V, 5A on -12V and 6A on 5V
- Two side-mounted power switches
- Two 1.8m power cords
- Power adapters included
- High-quality Penn Elcom components
- Super-comfortable Luxe carrying handle
- Anti-slip rubber feet
- Completely assembled, wired, tested, and ready to play!
Dimensions (L/W/H)
- 70,5 cm x 37,5 cm x 25 cm
Total Weight
- 11,9. kg (includes rails, power supplies, and other hardware)
Module depth
- 6,9 cm available depth between top of rail and bottom of case
- 6.2 cm available depth between top of rail and busboard
- 4.2 cm available depth between top of rail and protection plate PSU part
- 5.3 cm available depth between top of rail and top of header on busboard
MDLRCASE MDLR PWR powered busboard
MDLR PWR is a high precision low noise and high-powered bus board for your eurorack modular systems. With a total of 40 headers (per busboard) you’ll never run out of connectivity, so all your beloved modules can be easily connected. MDLR PWR is universal so it can accept a wide range of mains voltages from 100V to 240V and so this can be used worldwide. MDLR PWR is fed with an external power brick which takes care of no high voltages inside the case.
MDLR PWR is available in two different types: 45W and 85W.
Outputs:
MDLRPWR 45W
Power 45W
+12V / 2A
-12V / 1.2A
+5V / 1.5A
MDLRPWR 85W
Power 85W
+12V / 4A
-12V / 2,5A
+5V / 1.5A
Technical specifications:
Dimensions 420 x 140mm
Height 23mm
Weight 400g
Output stability ±1% for 0-100% load
Input 18V ( 16V – 20V )
Output Connectors 40 x 16 pin IDC for flat cable
Input connectors WAGO spring terminals + 5.5 / 2.1 DC inlet
Efficiency 92%
Protections:
Input overvoltage
Input reverse polarity
Output overvoltage
Output short current – automatic recovery
Output overcurrent – automatic recovery
All output protections are independent for each rail
- Other Input common-mode LC filter with high efficiency of canceling noise and interference from input connector
- Additional input filter on each regulator for minimal output noise and interferences
- Shield for reducing RF interferences from regulators
- Star distribution topology on PCB
- Each “beam” from star topology has 4 headers with noise canceling capacitors.
- In star topology center are another noise canceling capacitors
- A big ground plane on both sides of PCB
- Blue LEDs indicate present and drop of output voltage
- Recommended power brick for one board – Mean well GSM60A18-P1J
| _hp | 126 |